Ramsey-winch HDP35000 - Plantetary Industrial Winch Bedienungsanleitung

OPERATING, SERVICE AND MAINTENANCE MANUAL MODEL HD-P35,000INDUSTRIAL PLANETARY WINCHWITH AIR TENSIONER AND 2 SPEED MOTORCAUTION: READ AND UNDERSTAND

12151512141426263. Stand winch up on gear box end as shown. Remove winch tie plates #26 by removing (8) capscrews #12, (8) lock washers #14, and (4)

4. Pull motor end bearing #5 from drum assembly #1. Remove motor cou-pling #4 from input shaft. Pull drum assembly #1 from gear end bearing #6. Remov

5. If splines inside drum driver #102 are damaged, drum driver must be replaced. Remove drum driver by unscrewing (8) capscrews #105. If bushings sho

6. Remove output shaft #8 from gear end bearing #6. Inspect output shaft for dam-age or wear. Replace if damaged. Remove gear end bearing by removing

7. Remove clutch housing #23 with piston #16 and clutch #3 inside from gear box assembly #32. Inspect clutch for wear or damage and replace if re-qui

UNDERWOUND WINCH MOUNTING CONFIGURATIONR.H. MOUNTINGCONFIGURATIONUNDERWOUNDL.H. MOUNTINGCONFIGURATIONUNDERWOUND 12

OVERWOUND WINCH MOUNTING CONFIGURATION13R.H. MOUNTINGCONFIGURATIONOVERWOUNDL.H. MOUNTINGCONFIGURATIONOVERWOUND

6.98177,295.32135,128.56217,429.05228,6.7819,8116.00406,413.96354,5816.15410,21.81 Dia. CABLE ANCHOR10.72272,2840.841037,33Ø14.88377,95FLANGEØ6.00152,

5.06(128,58)5.32(135,12)8.25(209,63)8.56(217,42).78 (TYP)(19,18)7.10(180,28)16.62(422,21)10.13(257,18)10.69(271,56)16.14(410,05)36.96(938,78).81 CABL

5.06(123,58)7.10(180,28)6.27(159,38).78 (TYP)(19,79)8.56(217,4)16.62(422,21)10.13(257,18)10.69(271,56)14.27(362,56)35.09(891,29).81 CABLE ANCHORØ6.00

TABLE OF CONTENTSINTRODUCTION ... 1WARRANTY

171818b18c718a11132031930174512362324298282432192527101212121214141414151515152122262632a32a33************SEE BILL OF MATERIAL**33*3333**16HDP 35,000

PARTS LIST - HDP 35,00018Item No. Qty Part No. Description Item No. Qty Part No. Description1 1 234245 DRUM ASSEMBLY 19 1 456008 RELIEF FITTING* 1 234

103109106101108102107104105Item No. Part No. Quantity Description101 332196 1 DRU M-CABLE102 332283 1 DRIVER-DRU M103 412087 1 BUSHING104 412088 1 BU

Item No. Part No. Quantity Description101 234250 1 DRU M-CA BLE102 412087 1 BU SH IN G103 412088 1 BU SH IN G104 462052 1 O-RIN G105 462054 1 O-RIN GD

21320120421220320820620620920220920820521220520721021121CABLE TENSIONER - 299761 & 299763Item No. Part No. Quantity Description201 265119 1 LEVER

See warranty card for details.LIMITED WARRANTYRAMSEY WINCH COMPANYPost Offi ce Box 581510 Tulsa, Oklahoma 74158-1510 Telephone: (918) 438-2760 FAX: (91

Weight (without cable)...504 lb. (226 Kgs.)Rated Line Pull (lbs.)...

WARNINGS:CLUTCH MUST BE TOTALLY ENGAGED BEFORE STARTING THE WINCHING OPERATION.DO NOT START WINCH MOTOR BEFORE ENGAGING CLUTCH.DO NOT DISENGAGE CLUTCH

HYDRAULIC SYSTEM REQUIREMENTSRefer to the performance charts to properly match your hydraulic system to HDP-35000 winch performance. The charts consis

WINCH OPERATIONThe best way to get acquainted with how your winch operates is to make test runs before you use it. Plan your test in advance. Remember

MAINTENANCEAdhering to the following maintenance schedule will keep your winch in top condition and perform-ing as it should with a minimum of repair.

INSTRUCTIONS FOR OVERHAUL DIS-ASSEMBLY1. Drain oil from gear housing by removing oil drain plug, pipe plug #19 and relief fi t-ting #25. Remove tensio

30171818b18c718a1113203192. Disconnect tube #30 from valve #31 and fi tting #17 on brake #18. Remove motor #20 and gasket #18a by removing (2) capscre