OPERATING, SERVICE ANDMAINTENANCE MANUALMODEL RPH 15,000 PLANETARY WINCHCAUTION: READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION ANDOPERATION OF W
Remove tie plates (item #11) from end bearings (items #3 & #6) by unscrewing capscrews (item #18), asshown. Slide motor end bearing (item #3) fro
Generously apply grease (MOBILITH SHC 007) to teeth of ring gear (item #5), teeth of planet gears in drum (item#1) and to bushing in end bearing (item
Set winch on gear housing end with motor end bearing up. Insert (6) springs (item #42) into pockets of motor endbearing. Install coupling (item #25) o
Place gasket (item #29) into position on mounting surface of motor (item #31). Slide motor shaft into coupling andattach motor to brake housing (item
14* NOTE: THESE HOLE LOCATIONS MUST BE HELD WITHIN ±.03" (0,8 mm) OF TRUE POSITION. RECOMMENDED MOUNTING HOLE DIAMETER IS .66" (16,8 mm).SHO
15DRUM DIM DIM DIM DIM DIM DIMSIZE A B C D E F*STD 34.32 18.93 8.53 7.06 14.12 18.69871.7 480.8 216.7 179.3 358.6 474.7SHORT 29.07 16.37 5.97 4.50 9.
4937MODEL RPH 15,000WITH MANUAL CLUTCH SHIFTER18141115150402219124653862122418452616232031203911279428433034233936717294825244326353444133210474116
ITEM QTY. PART NO. DESCRIPTION ITEM QTY. PART NO. DESCRIPTION1 1 234173 STD. DRUM ASS'Y. 25 1 431015 COUPLING - BRAKE1 234200 SHORT DRUM ASS&apo
5339MODEL RPH 15,000WITH AIR CYLINDER CLUTCH SHIFTER20151216154432421137823262050281825223315401229105304732446351038919315227264728373649617422344143
ITEM QTY. PART NO. DESCRIPTION ITEM QTY. PART NO. DESCRIPTION1 1 234173 STD. DRUM ASS'Y. 26 2 418218 LOCKWASHER - 1/2 ID MED. SECT.1 234200 SHOR
TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIMITED WARRANTYRAMSEY WINCH warrants each new RAMSEY Winch to be free from defects in material and workmanship for a peri-od of one (1) year from dat
RAMSEY HYDRAULIC PLANETARY WINCH MODEL RPH 15,000PLEASE READ THIS MANUAL CAREFULLYThis manual contains useful ideas for obtaining the most efficient o
WINCH MOUNTINGESSENTIAL MOUNTING INSTRUCTIONS TO MAINTAIN ALIGNMENT OF PLANETARY WINCH COMPONENTSIt is most important that this winch be mounted sec
CABLE INSTALLATION1. Unwind cable by rolling it out along the ground to prevent kinking. Securely wrap end of cable, opposite hook,with plastic or s
HYDRAULIC SYSTEM REQUIREMENTSRefer to the performance charts below to properly match your hydraulic system to the winch performance. Thecharts consi
OPERATIONThe best way to get acquainted with how your winch operates is to make test runs before you actually use it. Planyour test in advance. Reme
CONDITION POSSIBLE CAUSE CORRECTIONWinch not mounted squarely, causing end bearings to bind up drum.Check mounting. Refer to WINCH MOUNTING page 4.Bra
INSTRUCTIONS FOR OVERHAUL OF RAMSEY WINCHMODEL RPH 15,000DISASSEMBLYTake note of mounting configuration for proper mounting of parts during re-assembl
Kommentare zu diesen Handbüchern